SVETELEKTRO

I'm stuck here..

Everytime I measure resistors higher than 10k, It is read as capacitors like 60-110uF..

Any ideas?


BR

Version 1.09m is out..

http://www.mikrocontroller.net/svnbrows ... /Software/


I will try this version later..

My final tester...ready for repairs.. :finga: https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-ash4/1009780_10201037280926228_2078309639_n.jpg https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash3/1013924_10201037280606220_633243146_n.jpg https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash4/1044...

I was looking also for some modification to display uH instead of mH for low value inductors. Cosmetic modification of displayed results (measuring inductance) does not improve accuracy. Yes exactly. but there are people who are used to read uF instead of nF, same with uH and mH. I'm used to read 2...

tom666 napísal:Hi Kasamiko,
nice design

Thanks tom


I was looking also for some modification to display uH instead of mH for low value inductors.

Here is my version running the latest 1.08k firmware with zener diode test.. Testing a 220uH Coil: https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash3/267214_10201031753388043_1370853465_n.jpg Testing 10,000uF 50V capacitor: https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-prn1/1010065_102010317...

Hi tom666,


I can't find the source code for version 1.08. Are the files with latest age like 4 days are added new? I mean the files for version 1.08?

Also does the meter capable of in-circuit measurement particular on ESR?


Regards

Hi tom, Thanks for the link. So what's new with version 1.08? Hod sem prosim foto PCB (stranu spoja a stranu suciastok). Vyzera to na problem s blokovanim AVCC - kondik musi byt umiestneny co najblizsie k prislusnemu pinu MCU (Pin 20 - DIP puzdro). Na vstup LDO doporucujem elyt (napr. 20uF). Este sk...

Hi tom666, I successfully built the meter But encountered this weird meter behavior. I can measure transistors, LED,diode, resistors, small value capacitors but above 0.1uF the device will SHUTDOWN.. Same with inductors, any value the meter will shutdown. Now weird thing is, if my programmer (AVRISP...

Hi tom666, Thank you for your reply.. :D We have found the culprit..than to Karl! Since I used Notepad to edit the MAKEFILE, and I never noticed it is SAVE AS UNICODE instead of ANSI format, which adds some fancy character on the MAKEFILE. :lol: See attached image. When I save it to ANSI format all ...

dobrý deň, Potom, čo robí nejaký výskum Google, som bol schopný skompilovať .. pomocou dodávaného Makefile. Ale ja som uviazol s ATmega168 iba. Už som sa snažil to: # Select your Part-No. for avrdude : # atmega8 : m8 # atmega168: m168 or m168p # atmega328: m328 or m328p PARTNO = m328 Je zvyknutý kom...

Snažil som sa kompilovať zdrojový kód pre ATmega328 s kryštálom 8 MHz na AVR Studio 4, ale zlyhal. Nižšie sú uvedené chybové správy. Makefile:81: warning: overriding commands for target `GetESR.o' Makefile:60: warning: ignoring old commands for target `GetESR.o' Makefile:90: warning: overriding comm...